logo
NOTICE:  This is the new PunchCAD forum. You should have received an email with your new password around August 27, 2014. If you did not, or would like it reset, simply use the Lost Password feature, and enter Answer as the security answer.
Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error
Shelled Solids - Modify Shelled Solids More Granularly
Options
Go to last post Go to first unread
Previous Topic Next Topic
ZeroLengthCurve  
#1 Posted : Sunday, September 11, 2022 12:38:01 AM(UTC)
ZeroLengthCurve

Rank: Senior Member

Joined: 5/15/2008(UTC)
Posts: 985

Thanks: 16 times
Was thanked: 32 time(s) in 23 post(s)
Would it make sense to allow some of the following?

— de-shell a solid body
— remove inner-shell edges of a shelled body

— (other than scale) deep-select one or more inner edges of a shelled body and move push/pull/extend/retract, in effect creating a differentially-shelled body, meaning the left/right sides could be shelled to, say, 22mm and the front/back to 15mm, the bottom to 30mm, and the top to 28mm

— make a scaled surface that is extracted from a shell remain properly distant from the parent solid


ZeroLengthCurve
Back to top
UGMENTALCASE  
#2 Posted : Sunday, September 11, 2022 10:19:49 AM(UTC)
UGMENTALCASE

Rank: Senior Member

Joined: 3/21/2017(UTC)
Posts: 946
Man
United Kingdom

Thanks: 46 times
Was thanked: 303 time(s) in 205 post(s)
I think you can in the inspector. Pick the shell in the concept explorer and you get a list of faces in the inspector. Select a face and then change the size. Some of those features are clunky as so I could be wrong there
Back to top
thanks 1 user thanked UGMENTALCASE for this useful post.
ZeroLengthCurve on 9/17/2022(UTC)
2murray  
#3 Posted : Saturday, September 17, 2022 1:38:31 AM(UTC)
2murray

Rank: Member

Joined: 2/15/2022(UTC)
Posts: 21

Was thanked: 27 time(s) in 18 post(s)
You can modify|thicken an inner face of a shelled solid, it stays part of the parent solid as an additional parametric feature, you can also offset or move but those give differing thickness results if the face isn't planar.

Edited by user Saturday, September 17, 2022 1:42:14 AM(UTC)  | Reason: Not specified
Back to top
thanks 2 users thanked 2murray for this useful post.
damhave on 9/17/2022(UTC), ZeroLengthCurve on 9/17/2022(UTC)
ZeroLengthCurve  
#4 Posted : Saturday, September 17, 2022 2:55:14 PM(UTC)
ZeroLengthCurve

Rank: Senior Member

Joined: 5/15/2008(UTC)
Posts: 985

Thanks: 16 times
Was thanked: 32 time(s) in 23 post(s)
Thanks, UgmentalCase amd 2Murray,

I neglected/failed to remember that, thanks to, on deep select and being unable to separate the cutter from the solid, and just getting a error message.


I was so transfixed with the initial issue of the cutter joing/fusing with the cut that I completely forgot that (for the good/achieved shells) I needed to select the whole body to get the Data tab to ahow the shell values, whereas simply single-clicking the body (so far as I've experienced) only shows minimal, other info on the Data tab. (Some of that I did around December, but after spending months on other things, I lost that misvle memory.)

It (editing the shell values) indeed IS a neat functionality. It lets me edit the compartment side shell to be, say, 22mm, and then fwd/aft bulkhead to be 11mm, to compensate for, after slicing then shelling, the adjacent bulkheads being 2x as thick as needed/desired.


Again, thanks!

ZLC
Back to top
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF.NET 2.1.2 | YAF.NET © 2003-2024, Yet Another Forum.NET