logo
NOTICE:  This is the new PunchCAD forum. You should have received an email with your new password around August 27, 2014. If you did not, or would like it reset, simply use the Lost Password feature, and enter Answer as the security answer.
Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error
Easy question: removing material from edge? (#3835)
Options
Go to last post Go to first unread
Previous Topic Next Topic
misterrogers  
#1 Posted : Friday, July 1, 2011 7:44:21 AM(UTC)
misterrogers

Rank: Senior Member

Joined: 8/14/2009(UTC)
Posts: 444
I want to remove material from an edge of a block as shown: Can I do this without creating a profile and using the cutout-solid tool? I was hoping the Lip or Groove tool could handle this.. didn't work.
misterrogers attached the following image(s):
Picture 2.png (16kb) downloaded 6 time(s).

You cannot view/download attachments. Try to login or register.
Back to top
ZeroLengthCurve  
#2 Posted : Friday, July 1, 2011 11:11:34 AM(UTC)
ZeroLengthCurve

Rank: Senior Member

Joined: 5/15/2008(UTC)
Posts: 989

Thanks: 19 times
Was thanked: 37 time(s) in 25 post(s)
By "without creating a profile", do you mean:

-- without using a cylinder of desired diameter/radius to interference delete the unwanted material?

-- without using a radius swept down the path of the corner where the material can be exploded from or trimmed out?

It sounds that you want the tool to isolate and reverse the corner face material in maybe two steps:

-- select the corner face to be inverted
-- deflect or offset and radius the corner by the amount entered


That would indeed be a very fast tool... I haven't tried to do such work, so I haven't explored the existing tools for the capability.
Back to top
misterrogers  
#3 Posted : Friday, July 1, 2011 12:23:33 PM(UTC)
misterrogers

Rank: Senior Member

Joined: 8/14/2009(UTC)
Posts: 444
Originally Posted by: ZeroLengthCurve Go to Quoted Post
By "without creating a profile", do you mean:

-- without using a cylinder of desired diameter/radius to interference delete the unwanted material?

-- without using a radius swept down the path of the corner where the material can be exploded from or trimmed out?

It sounds that you want the tool to isolate and reverse the corner face material in maybe two steps:

-- select the corner face to be inverted
-- deflect or offset and radius the corner by the amount entered


That would indeed be a very fast tool... I haven't tried to do such work, so I haven't explored the existing tools for the capability.




You hit the nail on the head. Ideally I'd like with one tool, to be able to click on an edge or two intersecting faces and remove material along both axes with a given value for each.

It is not unlike the Groove tool except that it wouldn't remove material along the edge of the whole face only one edge.

This comes in handy for furniture so parts that meet have a small gap during finishing and therefore if parts don't get lined up perfectly during production, it doesn't look funny. Basically the small 1-2mm gap helps prevent the negative appearance of slightly misaligned parts. Since this occurs on all visible parts, it would save so much time having one tool to do this with one operation. I'm sure there may be other (better?) uses for other folks..
Back to top
billbedford  
#4 Posted : Saturday, July 2, 2011 2:28:11 AM(UTC)
billbedford

Rank: Senior Member

Joined: 2/19/2007(UTC)
Posts: 186
You can do this with the new push-pull tool in the new v8 beta.
Back to top
zumer  
#5 Posted : Saturday, July 2, 2011 10:44:23 AM(UTC)
zumer

Rank: Senior Member

Joined: 11/4/2007(UTC)
Posts: 515

Was thanked: 1 time(s) in 1 post(s)
Place a block by three points from one corner of your workpiece and subtract it. Finds its own workplane, parameters easy to assign in the data boxes.
zumer attached the following image(s):
quick lip.JPG (37kb) downloaded 5 time(s).

You cannot view/download attachments. Try to login or register.
Back to top
misterrogers  
#6 Posted : Saturday, July 2, 2011 11:38:45 AM(UTC)
misterrogers

Rank: Senior Member

Joined: 8/14/2009(UTC)
Posts: 444
Yeah the push pull would be very handy.. just place a line extending from one end to the other and push back a given distance.

Zumer - that's what I've been doing, but it just adds additional steps that I wish I didn't.. That's why I was hoping for a tool that requires only one step for time's sake alone.
Back to top
zumer  
#7 Posted : Sunday, July 3, 2011 7:49:59 AM(UTC)
zumer

Rank: Senior Member

Joined: 11/4/2007(UTC)
Posts: 515

Was thanked: 1 time(s) in 1 post(s)
You're right, it doesn't make sense that the tool button picture implies that it will treat an edge, not its actual face treatment.
Back to top
Users browsing this topic
Guest (4)
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF.NET 2.1.2 | YAF.NET © 2003-2024, Yet Another Forum.NET