logo
NOTICE:  This is the new PunchCAD forum. You should have received an email with your new password around August 27, 2014. If you did not, or would like it reset, simply use the Lost Password feature, and enter Answer as the security answer.
Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error
3 Pages<123>
2 rail sweep. (#2395)
Options
Go to last post Go to first unread
Previous Topic Next Topic
Steve.M  
#21 Posted : Monday, June 15, 2009 11:58:11 PM(UTC)
Steve.M

Rank: Senior Member

Joined: 6/18/2008(UTC)
Posts: 978

Was thanked: 1 time(s) in 1 post(s)
Well after trying to find out what is happening, I have come to the conclusion that the 2 rail sweep can work, although it can be a case of having to attempt it a few times. :rolleyes:

An example of this is below.
01: 2 circles as rails with a rectangle as section to sweep
02: the result when the inside circle is picked first for the rails (incorrect)
03: After selecting the outside circle first for the rails, the correct result.

This does not always work, sometimes the rails need to be changed to other spline types, then a case of picking the correct rail first. So it is a little unpredictable, but can usually now get a result eventually.

A bit of an "Hit or miss" situation.
Steve.M attached the following image(s):
01.jpg (36kb) downloaded 5 time(s).
02.jpg (136kb) downloaded 5 time(s).
03.jpg (123kb) downloaded 5 time(s).

You cannot view/download attachments. Try to login or register.
Back to top
unique  
#22 Posted : Tuesday, June 16, 2009 1:25:53 AM(UTC)
unique

Rank: Senior Member

Joined: 6/24/2008(UTC)
Posts: 591
Originally Posted by: Steve.M Go to Quoted Post
...........This does not always work, sometimes the rails need to be changed to other spline types, then a case of picking the correct rail first. So it is a little unpredictable, but can usually now get a result eventually.

A bit of an "Hit or miss" situation.


There should be no order in which to pick curves to build a surface/solid...this "should" be a relatively simple fix for Tim/Ryan?

If like you say it takes multiple attempts to get a satisfactory result (if you havent given up by then) then to me the HELP is either useless or poorly documented OR you havent bloody read it !:D
Back to top
Steve.M  
#23 Posted : Tuesday, June 16, 2009 6:26:54 AM(UTC)
Steve.M

Rank: Senior Member

Joined: 6/18/2008(UTC)
Posts: 978

Was thanked: 1 time(s) in 1 post(s)
Originally Posted by: unique Go to Quoted Post
If like you say it takes multiple attempts to get a satisfactory result (if you havent given up by then)
You should try it.
Originally Posted by: unique Go to Quoted Post
then to me the HELP is either useless or poorly documented OR you havent bloody read it !:D
The help file states nothing about pick order. nor the fact that rails need to be changed at times to other types for the rails to work. (Then again, there is nothing in the help file about pick order of sections for guide skin surfaces/solids.)

VC/Shark certainly does not appear to be a user friendly CAD, well certainly not on the PC.

- Steve
Back to top
Steve.M  
#24 Posted : Tuesday, June 16, 2009 7:53:48 AM(UTC)
Steve.M

Rank: Senior Member

Joined: 6/18/2008(UTC)
Posts: 978

Was thanked: 1 time(s) in 1 post(s)
Originally Posted by: unique Go to Quoted Post
If like you say it takes multiple attempts to get a satisfactory result


Example;-

http://rapidshare.com/files/245182773/2railsweep.avi
Back to top
Steve.M  
#25 Posted : Tuesday, June 16, 2009 9:00:03 AM(UTC)
Steve.M

Rank: Senior Member

Joined: 6/18/2008(UTC)
Posts: 978

Was thanked: 1 time(s) in 1 post(s)
An example where 2 trimmed ellipse are used for the rails:-

http://rapidshare.com/files/245202272/2ellipserail.avi
Back to top
unique  
#26 Posted : Tuesday, June 16, 2009 9:07:06 AM(UTC)
unique

Rank: Senior Member

Joined: 6/24/2008(UTC)
Posts: 591
Originally Posted by: Steve.M Go to Quoted Post
You should try it.


No thanks....I simply dont have the time or patience to muck about. Rhino produces this with just a few clicks and using nurbs curves, how many curves did you try :rolleyes::D:D
Back to top
Steve.M  
#27 Posted : Tuesday, June 16, 2009 9:25:58 AM(UTC)
Steve.M

Rank: Senior Member

Joined: 6/18/2008(UTC)
Posts: 978

Was thanked: 1 time(s) in 1 post(s)
Originally Posted by: unique Go to Quoted Post
I simply dont have the time or patience to muck about.
My major problems with this come when I have 2 closed CP spline rails, as if/when the 2 rail sweep fails I need to convert, the problem then being, if I change the rails to Bezier, then the start point changes, if I change them to Int, then the start/end angles are lost. Not a major problem if the splines are planer, but a lot of the sweeps I make are in 3d space, so it is a nightmare.

Originally Posted by: unique Go to Quoted Post

Rhino produces this with just a few clicks and using nurbs curves,
I have gone back to Rhino for quite a number of models I have built, simply because I want what is expected to be produced on the first attempt, not to have to mess around changing selection/types :(

- Steve
Back to top
Steve.M  
#28 Posted : Tuesday, June 16, 2009 10:26:20 AM(UTC)
Steve.M

Rank: Senior Member

Joined: 6/18/2008(UTC)
Posts: 978

Was thanked: 1 time(s) in 1 post(s)
Back to top
ZeroLengthCurve  
#29 Posted : Tuesday, June 16, 2009 1:00:31 PM(UTC)
ZeroLengthCurve

Rank: Senior Member

Joined: 5/15/2008(UTC)
Posts: 989

Thanks: 19 times
Was thanked: 37 time(s) in 25 post(s)
Is there a way to view these avi's without going thru rapidshare? If i can't directly click-n-run it or download for later review, i just close the page and think, "Next?"...
Back to top
jol  
#30 Posted : Tuesday, June 16, 2009 2:06:43 PM(UTC)
jol

Rank: Senior Member

Joined: 2/26/2007(UTC)
Posts: 2,156

Was thanked: 1 time(s) in 1 post(s)
Same .. I'm with shorty !
Back to top
Steve.M  
#31 Posted : Tuesday, June 16, 2009 2:19:55 PM(UTC)
Steve.M

Rank: Senior Member

Joined: 6/18/2008(UTC)
Posts: 978

Was thanked: 1 time(s) in 1 post(s)
Originally Posted by: jol Go to Quoted Post
Same .. I'm with shorty !
Click the links now for direct download.
Back to top
jol  
#32 Posted : Tuesday, June 16, 2009 2:37:08 PM(UTC)
jol

Rank: Senior Member

Joined: 2/26/2007(UTC)
Posts: 2,156

Was thanked: 1 time(s) in 1 post(s)
ooh Tim .. it's awful
Back to top
ttrw  
#33 Posted : Tuesday, June 16, 2009 3:32:55 PM(UTC)
ttrw

Rank: Senior Member

Joined: 4/1/2007(UTC)
Posts: 1,583

Was thanked: 2 time(s) in 2 post(s)
ouch. That hurts :o :o :(
Back to top
unique  
#34 Posted : Tuesday, June 16, 2009 5:16:30 PM(UTC)
unique

Rank: Senior Member

Joined: 6/24/2008(UTC)
Posts: 591
Originally Posted by: ZeroLengthCurve Go to Quoted Post
Is there a way to view these avi's without going thru rapidshare? If i can't directly click-n-run it or download for later review, i just close the page and think, "Next?"...


eh????? just hot run and direct thru media player or whatever player you have set as default. If you are a Mac user I have no sympathy....get a frickin PC:rolleyes::rolleyes:
Back to top
ttrw  
#35 Posted : Tuesday, June 16, 2009 5:20:21 PM(UTC)
ttrw

Rank: Senior Member

Joined: 4/1/2007(UTC)
Posts: 1,583

Was thanked: 2 time(s) in 2 post(s)
Actually, I may be mistaken, but I think zerolengthcurve is a PC user! :p

Works absolutely fine here! :D
Back to top
billbedford  
#36 Posted : Wednesday, June 17, 2009 4:54:07 AM(UTC)
billbedford

Rank: Senior Member

Joined: 2/19/2007(UTC)
Posts: 186
Originally Posted by: Steve.M Go to Quoted Post
An example where 2 trimmed ellipse are used for the rails:-


Sorry, but can you tell me exactly how you drew your rails. Whenever I try and reproduce your solid they come out as they are suposed to.
Back to top
nabed  
#37 Posted : Wednesday, June 17, 2009 5:18:02 AM(UTC)
nabed

Rank: Member

Joined: 2/18/2007(UTC)
Posts: 98
Originally Posted by: unique Go to Quoted Post
eh????? just hot run and direct thru media player or whatever player you have set as default. If you are a Mac user I have no sympathy....get a frickin PC:rolleyes::rolleyes:


Honestly, there are millions of places out there to have asinine arguments about PC/Mac
If You really feel the need to fight the oldest of all flame wars, I have no sympathy .... get a frickin‘ live.
Back to top
Steve.M  
#38 Posted : Wednesday, June 17, 2009 5:24:17 AM(UTC)
Steve.M

Rank: Senior Member

Joined: 6/18/2008(UTC)
Posts: 978

Was thanked: 1 time(s) in 1 post(s)
Originally Posted by: billbedford Go to Quoted Post
Sorry, but can you tell me exactly how you drew your rails.
I created one Ellipse from origin (X0,Y0,Z0), then created a second offset along the X, I then created a trimming line on the X axis and trimmed the bottom half from both Ellipse. see pic.
Originally Posted by: billbedford Go to Quoted Post
Whenever I try and reproduce your solid they come out as they are suposed to.
I have tried this now in VC Pro 835 and Shark 835 (both PC versions) with same result.(and checked on a second PC with same result)
Steve.M attached the following image(s):
01.jpg (56kb) downloaded 5 time(s).

You cannot view/download attachments. Try to login or register.
Back to top
jol  
#39 Posted : Wednesday, June 17, 2009 6:55:22 AM(UTC)
jol

Rank: Senior Member

Joined: 2/26/2007(UTC)
Posts: 2,156

Was thanked: 1 time(s) in 1 post(s)
I'd like to agree with Nabed .. there are lots of other places for that

besides, we have our work cut out here
Back to top
Steve.M  
#40 Posted : Wednesday, June 17, 2009 7:42:37 AM(UTC)
Steve.M

Rank: Senior Member

Joined: 6/18/2008(UTC)
Posts: 978

Was thanked: 1 time(s) in 1 post(s)
Originally Posted by: jol Go to Quoted Post
besides, we have our work cut out here

I agree.

Please, to all, I do not want this thread to go off topic. I believe these problems with the 2 rail sweeps need attention.

The only "Mac vs PC" I am interested in (in this thread), is if there is a difference in how the 2 rail sweeps are handled.


- Steve
Back to top
Users browsing this topic
Guest (15)
3 Pages<123>
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF.NET 2.1.2 | YAF.NET © 2003-2024, Yet Another Forum.NET